SlideRenu® is a revolutionary line of coatings that restore, protect and rejuvenate color faded water slides and wet ride attractions. Contact SlideRenu - We work Internationally! SlideRenu Company News & Events! Water Slide Restoration Projects featuring Before & After Photos! SlideCare FAQ Our Services include Water Slide Repairs, Restoration, Resurfacing, Inspection, & Maintenance. SlideCare Homepage - all about our Water Slide Restoration Company! Shop Our Huge List of Proprietary Water Slide Restoration & Maintenance Products! SlideCare Homepage - all about our Water Slide Restoration Company!
 
 
StairTape Non-Slip Safety Tape

<- Back to Shop Products DOWNLOAD PDF  

 

SlidePatch™ Fast Cure Fiberglass Repair Kit

DESCRIPTION
SlidePatch™ is a 2 component FAST CURING water proof epoxy resin finishing paste that is used to repair fiberglass water slide surface imperfections, scratches and gouges. SlidePatch™ resin and hardener comes in PRE-MEASURED tubes which eliminates the need to measure and mix the exact ratios of fiberglass resin and hardener. Work time is FAST, 1-2 minutes, and the repair area can be sanded within 20 minutes after it is applied. It can be painted within 1 hour (full cure time) so your water slides can be quickly put back into service. Compatible with all types of paints and plastics including gel-coat, epoxy, urethane, solvent based paints and polypropylene plastic.

The Kit includes:
• 10.1 oz. Resin & Hardener
• Plastic Spreader
• Fiberglass Mesh
• 80 Grit Sandpaper

STORAGE
Product should be stored in well ventilated areas between 50°F (10°C) and 70°F (21°C) prior to use. KEEP FROM FREEZING and KEEP FROM EXTREME HEAT. Keep cartridges closed when not in use. Empty cartridges should not be reused.

SHELF LIFE
To obtain best performance, use this product within 6 months from date of manufacture.

SAFETY
Use neoprene, nitrile or rubber gloves to prevent skin contact. Wear long sleeve shirt and safety glasses. Respiratory protection is not required under normal working conditions where adequate ventilation is present.

APPLICATION
Best results are achieved when applied to clean, dry surfaces at temperatures near 70°F (21°C). Minimum application temperature is 50°F (10°C). Clean the damaged area with SlideRenu® SlideDetergent™ degreaser and Calcitrol™ scale remover (follow label instructions). Hand sand the area to be repaired with 80 grit sandpaper. Rinse away all dust with water. Let dry. Wipe damaged area with a clean white cloth and MEK or ACETONE solvent. Let dry. Insert the dual cartridge tube into the dual-cartridge dispensing gun (required). Remove the white end plug and screw on the red static mixer. Squeeze the dispensing gun trigger slowly to make sure the resin and hardener completely travel the entire length of the red static mixer. Push out the desired amount of paste on the repair area and spread out using the plastic spreader. Apply fiberglass mesh (if needed) as soon as the paste is spread out. WORK TIME IS ONLY 2 MINTUES. Immediately after use, remove the red static mixer and put the white end plug back on the tube to prevent the paste from hardening over the dispensing hole. Properly dispose of used red static mixer. If a second application is needed, it should be done after the first application has cured (1 hour). Final cure strength is attained in 1hour at 70°F (21°C).

CLEAN-UP
Use mineral spirits to clean tools and unwanted past sealer from the water slide surface. Wash hands with a mild citrus-based soap.

FIRST AID
This material is not likely to be hazardous by inhalation. However, if exposed to excessive levels of vapor or mist, remove to fresh air, give oxygen if breathing is difficult, and get immediate medical attention. If swallowed, do not induce vomiting. Give victim one or two glasses of water or milk. Call a physician immediately for further instructions. Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention. Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water.

This product is available in 10.1 oz. or 300 ml. tubes and sold exclusively by SlideCare, LLC.


<- Back to Shop Products DOWNLOAD PDF ^ To Top^ 

 
MSDS Product Safety Label
Environmentally Friendly Product Leaf
SlideCare, LLC
3428 Napa Boulevard Suite 1971 • Avon, Ohio 44011
Tel: 440.930.2490 • Fax: 440.653.5100
info@SlideRenu.com